<h2>Shower Door Sweep Replacements: Keep The Water In The Shower!</h2>What is a shower door sweep replacement and why do you need one? A shower door sweep is a vinyl and polycarbonate strip that snaps onto the edges of frameless shower doors to prevent water from dripping out of the shower. Shower sweeps make bathroom and shower cleaning easy because they trap all of the water from your shower inside the shower area, reducing the risk of mildew or bacterial growth outside your shower. Since shower sweeps snap on, they require very few tools and no adhesives to install remove, and replace. Already know what you want? <a href="/hardware-and-accessories/shower-door-sweeps">Buy shower door sweeps online</a>!<h2>Types Of Shower Door Sweep Replacements</h2>&nbsp;<figure class="image image_resized" style="width:75%;"><img src="https://dgm-dgm-cms-service-stg.s3.amazonaws.com/Sweep_06_e55277af90.jpg" alt="Sweep-06.jpg"></figure>If you need to replace your shower sweep, Dulles Glass has you covered. There are three types of shower door sweeps: bottom sweeps, side sweeps, and door jamb sweeps. Bottom shower door sweeps go on the bottom of your shower doors and prevent water from leaking out of the bottom of your shower area. Side sweeps go on the side of the shower door that opens outward, while door jamb sweeps go on the hinged side of the shower door. Additionally, make sure you determine whether you need glass-to-glass or wall-to-glass shower sweeps. Glass-to-glass shower door sweeps are inserted vertically between two shower glass panels while wall-to-glass shower sweeps are inserted vertically between a shower glass panel and a wall.<h2>Shower Door Sweep Replacement &amp; Drip Rail</h2><figure class="image image_resized" style="width:75%;"><img src="https://dgm-dgm-cms-service-stg.s3.amazonaws.com/Sweep_05_05c5b73d3a.jpg" alt="Sweep-05.jpg"></figure>You should replace your frameless shower door sweep anywhere from 6 to 24 months. Shower door sweeps lose their seal over time and are not as effective at keeping in water. You should also replace your shower door sweep if it is discolored, cracked, or brittle, or shows other signs of wear and tear. Our shower door sweeps fit glass shower doors that are 1/4", 1/2", and 3/8" of an inch thick and can be 98 inches long for door jamb sweeps or 36 inches long for bottom sweeps. Additionally, you can cut the longer-length shower door sweeps to size so that they will fit your shower.<h2 style="margin-left:0px;">How To Install Shower Door Sweep Replacements And Bottom Seals</h2><figure class="image image_resized" style="width:75%;"><img src="https://dgm-dgm-cms-service-stg.s3.amazonaws.com/Sweep_01_92daa80d65.jpg" alt="Sweep-01.jpg"></figure> Once you receive your shower door sweep, you will need to do a few things prior to installing it. After removing your worn shower door sweep, carefully use a glass scraper to remove any residue from the area to ensure that the new shower sweep fits perfectly. Next, clean the area with glass cleaner and a microfiber cloth. Now your shower door is ready; you can install your new shower door sweep. Check out the video for more on how to do that. And don't forget, you can clean your shower sweeps whenever you clean your shower, just don't use harsh cleaners on them.&nbsp;<div class="raw-html-embed"><iframe src="https://www.youtube.com/embed/ECdXEAAIBFI?enablejsapi=1" title="How To Install a Bathtub Screen | DIY Installation Instructions TroySystems" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" allowfullscreen=""></iframe></div>

Learn the steps for replacing and installing bathtub and shower door sweeps and seals. These will help maintain a clean bathroom and prevent water leakage.

Types Of Shower Door Sweep Replacements And How To Install Shower Sweeps

How to Replace & Install Bathtub and Shower Door Sweep and Seals

If you're looking to upgrade your bathtub with a sleek and modern look, a frameless <a href="/shower-doors/bathtub-enclosures-doors-and-screens">bathtub glass door</a> or panel may be just what you need. Not only does it add an aesthetic appeal, but it also keeps the water in the bathtub and out of your bathroom floor. However, installing a frameless glass bathtub door or panel may seem daunting, especially if you're not a DIY expert. In this blog post, we'll guide you through the step-by-step process of installing a frameless glass bathtub door or panel, so you can achieve the bathroom of your dreams.<h2> The Bathtub Door Installation Guide</h2>Installing DIY glass bathtub doors and panels is quite easy with the help of our video guide, making the installation process clear and straightforward. Our video guide will provide a visual representation of the process to help you along with the installation. With the right tools, you can install your own glass bathtub doors and panels in no time. Plus, by doing it yourself, you can save money on installation costs and have the satisfaction of completing a home improvement project on your own.Before you start your installation, you must ensure to protect the glass by placing the glass onto the cardboard, blanket, or soft surface. Do not allow the glass or its edges to come in contact with hard surfaces such as tile or ceramic.&nbsp;<div class="raw-html-embed"><iframe src="https://www.youtube.com/embed/I3bU8vCJsiU" title="How To Install a Bathtub Screen | DIY Installation Instructions TroySystems" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" allowfullscreen=""></iframe></div>To download a Bathtub Door Installation Manual in PDF, please <a href="https://dgm.azureedge.net/pdfs/installation-manual-bathtub-screen.pdf">click here.</a> &nbsp; &nbsp;<h2>The Bathtub Door Installation Process &nbsp;</h2>Installing DIY bathtub glass doors and glass panels can be a straightforward process when following these easy steps:Materials:<ul><li>Glass door or panel</li><li>Wall anchors&nbsp;</li><li>Screws</li><li>Drill</li><li>Screwdriver</li><li>5/16" Diamond Tipped Drill Bit</li><li>Silicone Caulk Gun</li><li>Rubber Mullet</li><li>Measuring tape</li><li>Painters Tape</li><li>Utility Knife</li><li>48" Level</li><li>Suction Cup</li><li>Drop Cloth</li><li>Pencil</li><li>Wire Cutter</li></ul>&nbsp; Step 1: Attach the Brackets to the WallPlace the brackets onto the notches of the glass, and screw them in but do not fully tighten them -- just enough so that they stay on but are still adjustable. Allen screws should be facing inside the bathtub, so they are hidden from the outside view. Do the same for the top and bottom hinges.The reason hinges have to be installed at this time is to mark up the proper holes on the wall for drilling. Place plastic shims onto the tub where the glass screen will be installed. This will create a 7/16ths of an inch gap between the glass and tub surface. This gap is a placeholder for the drip edge plastic sweep at the end of the installation.Step 2: Measure and Drill HolesPlace the glass door on top of the shims. Have a friend help you with lifting and holding the glass. Move the glass screen up against the wall and Place a level up against the glass so that it is perfectly level. Mark up the holes for the hinges while still holding the glass perfectly level. There will be 4 holes per hinge, 2 on the outside and 2 on the inside for both the top and bottom hinge. After marking the holes, carefully remove the glass screen, and place it back onto a soft surface.Drilling the Holes into Studs: Holes will be 3/16th of an inch and will be drilled with a spade tip tile drill bit. Drill your 4 holes per hinge into the stud. Tap the included plastic anchors into the holes with a plastic mallet. If necessary, cut the head of the anchors with a razor to make the wall surface flush.Step 3: Attach Hinges to WallPlace the door back on top of the shims on the tub. Make sure that the holes are aligned with your hinges. Install the top hinge first. Start with the top outside hole and tighten the screw slightly, Make sure not to over-tighten the screws.Next, install the outside bottom screw followed by the inside top screw, and then the inside bottom screw -- completing the installation of the top hinge to the wall and then the bottom hinge installing the screws in the same order as the top hinge.Step 4: Attach the Glass Door or Panel to the HingesAttach the glass door or panel to the hinges using the provided screws. Make sure the door or panel is level and straight. Now open and close the glass door a few times to ensure proper movement of the glass panel. Once satisfied with the screen movement, use a manual screwdriver for the final turns of the screw to make the hinges completely secured to the wall.The next step is taking the included Allen wrench and tightening the hinges to the glass. Adjust and turn the Allen screws (first the top, then the bottom screws), to make sure the glass is secured to the hinge.Step 5: Install a Door Handle or Door KnobThis step depends on the type of hardware you have chosen for your glass panel and will involve placing the attachment hardware through the provided opening and securing the hardware from both sides. Make sure to tighten the screws securely, but do not overtighten them as this can crack the glass. Test and adjust the handle or knob to ensure that it is securely attached and functions properly. Adjust as necessary.Please make sure to use the provided washers with your hardware to avoid contact between glass and metal at all times.Step 6: Install SweepsInstalling shower door sweeps on a bathtub glass door is a fairly simple process that can be done with a few basic tools. First, clean the bottom of the glass door with rubbing alcohol to ensure a proper seal.&nbsp; First, remove&nbsp;the shims so the door can swing out 90 degrees. The bottom sweep is pre-cut and is included. The side of the plastic sweep with the V end will be facing inside the shower. Snap the plastic sweep onto the bottom of the screen and slide it all the way on, tapping it onto the screen so that it is flush.Next, measure and clip on the plastic sweep for the sides of the glass. After measuring the 3 different pieces of the plastic sweep, cut them with cutting pliers and snap them on for a clean installation. Have the lip of the plastic sweep facing inside the tub, as you did with the bottom sweep. It is important to make sure the sweep is level and flush with the door to ensure a tight seal. With proper installation, shower door sweeps can help prevent water leakage and keep your bathroom clean and dry.Step 7: Adjust and Tighten&nbsp; Adjust and Tighten Adjust the glass door or panel as needed to ensure that it opens and closes smoothly. Tighten all screws to ensure that the door or panel is secure.Step 8: Clean Up Clean Up Clean the glass door or panel and the surrounding area to remove any debris or fingerprints. With these easy steps, you can install DIY bathtub glass doors and glass panels in no time. Remember to take your time, follow the instructions carefully, and use the proper tools and materials for a successful installation.

Learn how to install a frameless bathtub glass door or panel for a modern bathroom upgrade. Our guide will make your DIY installation easy and rewarding.

How to Install DIY Bathtub Glass Doors or Glass Panels

How to Install DIY Bathtub Doors or Panels

Our Blog. Keep in touch with the latest glass, mirror and shower door trends, tips and trends by reading our blog, Reflections!

Dulles Glass Blog Page 11

How to Replace & Install Bathtub and Shower Door Sweep and Seals

How to Install DIY Bathtub Doors or Panels

Products

Support

Resources